|
|
| (3 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | ''Draft for a proper page if there's enough interest''
| + | Moved to → [[Fidget Cube]] |
| − | | |
| − | == Introduction ==
| |
| − | | |
| − | Fidget cubes are ...?
| |
| − | | |
| − | == Features ==
| |
| − | [[File:China_fidget_cube_open.jpg|thumb|right|200px]] | |
| − | All cubes have these common features that can be found on the sides of the device:
| |
| − | | |
| − | * Joystick
| |
| − | * Rocker switch
| |
| − | * 5 buttons, some are clicky and some silent
| |
| − | * Spinning disk
| |
| − | * 3 rollers/gears & rotating shiny ball
| |
| − | * Oval shaped indent (does nothing)
| |
| − | | |
| − | Exact implementations of these features can vary. For example, some cubes do have rubberized buttons while others don't, some cubes allow you to press/click the shiny ball, etc.
| |
| − | | |
| − | The body of the cube measures approximately 3 cm on each side (not including sticking out parts).
| |
| − | | |
| − | == Chinese Fidget Cubes ==
| |
| − | | |
| − | The following table shall give a short overview of some Chinese clones, their features and flaws.
| |
| − | | |
| − | {| class="wikitable"
| |
| − | ! Manufacturer
| |
| − | ! Joystick
| |
| − | ! Rocker switch
| |
| − | ! 5 buttons
| |
| − | ! Spinning disk
| |
| − | ! 3 rollers
| |
| − | ! Shiny ball
| |
| − | ! Oval indent
| |
| − | ! Price
| |
| − | ! Flaws
| |
| − | ! Notes
| |
| − | |-
| |
| − | | Ebay (rightyoung)
| |
| − | |
| |
| − | |
| |
| − | | Rubberized, 3 clicky, 2 silent
| |
| − | |
| |
| − | | No resistance
| |
| − | | Clicky
| |
| − | |
| |
| − | | ~$8
| |
| − | | Joystick
| |
| − | | Can be opened by lifting the rotating plate (with a knife or thin plastic tool) and undoing two small Philips screws underneath, comes apart without force. Rocker switch resistance is done with magnets.
| |
| − | |-
| |
| − | | Gearbest
| |
| − | |
| |
| − | |
| |
| − | | Plastic
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | | $5
| |
| − | | Joystick, build quality, loud buttons
| |
| − | |
| |
| − | |-
| |
| − | | Antsylabs (Kickstarter)
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | |
| |
| − | | $25
| |
| − | |
| |
| − | | Pre-order only
| |
| − | |}
| |
| − | | |
| − | === Common flaws ===
| |
| − | | |
| − | So far not too many people have shared their experiences on the [[Chink_shit_general|/csg/]] threads, but a few issues stick out:
| |
| − | | |
| − | * The joystick is prone to get stuck pretty quickly. This may be due to wear and tear on the metal ball inside, which rubs against a another metal plate, causing a flat surface there on the ball. Applying some grease might or might not help.
| |
| − | * Build quality is hit-or-miss.
| |
